W2008R2 Time 5 mns off

-

not sure happening, time (edt) on w2008r2 server consistently - , - 5 minutes fast time.    i've tried looking @ settings, changed time server to, time on server, , therefore on ad network, 5 minutes fast.  running exch 2010 on box, people answer emails appear "replies" earlier original messages! 

any thoughts appreciated.   thanks.

hello,

in network going not optimal. in situation kick out time configuration on dcs first , start fresh. go on domain member servers , clients. if use vms dc disable time sync host server.

first make sure machines in same time zone , adjust daylight time settings equal. go on reset of time on dc pdcemulator fsmo:

net stop w32time

w32tm /unregister

w32tm /register

net start w32time

now configure external time source:

w32tm /config /manualpeerlist:peers /syncfromflags:manual /reliable:yes /update

please set peers time source listed above, either it’s ip address or dns name. if more 1 needed separate them space in between , don't forget quotes: "time.domain.com time1.domain.com"

internet time servers can find here: http://www.pool.ntp.org/ make sure firewall port udp 123 opened.

now reset time on other dcs shown above , reconfigure time with:

w32tm /config /syncfromflags:domhier /update

after have run:
net stop w32time
net start w32time

and after working go on clients, remvoe configured settings , run:

w32tm /config /syncfromflags:domhier /update

after have run:
net stop w32time
net start w32time

best regards meinolf weber disclaimer: posting provided "as is" no warranties or guarantees , , confers no rights.


Windows Server  >  Windows Server General Forum



Comments

Post a Comment

Popular posts from this blog

WIMMount (HSM) causing cluster storage to go redirected (2012r2 DC)

-
looking options resolve error , prevent in future. thanks help. hardware: 2 node dell hv cluster running2012r2 dc 8 nic/ea in multiplex mode 4x hyper-v 4x hosts storage: 2x synology nas, accessed through iscsi hosts , cluster relevant logs: log name:      microsoft-windows-failoverclustering/diagnostic source:        microsoft-windows-failoverclustering date:          event id:      2050 task category: none level:         warning keywords:       user:          system computer:      l description: [dcm] filter wimmount found @ unsafe altitude 180700 log name:      system source:        microsoft-windows-failoverclustering date:         event id:      5125 task category: cluster shared volume level:         warning keywords:       user:          system computer: description: cluster shared volume 'volume1' ('cluster disk 1') has identified 1 or more active filter drivers on device stack interfere csv operatio
Read more

Failed to delete the test record dcdiag-test-record in zone test.com

-
ps c:\users\administrator.test> dcdiag /test:dns directory server diagnosis performing initial setup:    trying find home server...    home server = dc02    * identified ad forest.    done gathering initial info. doing initial required tests    testing server: default-first-site-name\dc02       starting test: connectivity          ......................... dc02 passed test connectivity doing primary tests    testing server: default-first-site-name\dc02       starting test: dns          dns tests running , not hung. please wait few minutes...          ......................... dc02 passed test dns    running partition tests on : forestdnszones    running partition tests on : domaindnszones    running partition tests on : schema    running partition tests on : configuration    running partition tests on : test    running enterprise tests on : test.com       starting test: dns          test results domain
Read more

Azure MFA with Azure AD and RDS

-
i have setup following lab in azure , need help. a server (domain controller) , remote desktop services. and server multi factor authentication server. i have setup following one http://www.rdsgurus.com/uncategorized/step-by-step-using-windows-server-2012-r2-rd-gateway-with-azure-multifactor-authentication/ and when im connecting got following error. the user "domain\username", on client computer "xxx.xxx.xxx.xxx", did not meet connection authorization policy requirements , therefore not authorized access rd gateway server. authentication method used was: "ntlm" , connection protocol used: "rpc-http". following error occurred: "23003". also on security log i've got following authentication details: connection request policy name: ts gateway authorization policy network policy name: - authentication provider: radius proxy authentication server: test.test.local authentication type: - eap t
Read more